With Governor Schwarzenegger declaring a drought and water bills out of sight, homeowners are focusing on water use like never before. We needn’t turn off the taps completely and go without gardens, but by planting low-water plants and then watering efficiently, we can both comply with the municipal requests to reduce water use and lower those bills!
Efficient watering means putting the right amount of water, in the right place, just at the plants needing it, without excess, runoff, overspray, or waste. The most efficient watering method available is drip irrigation--drip irrigation exceeds 90 percent efficiency, whereas sprinkler systems and hand watering are 50 to 70 percent efficient. For most home gardeners, the advantages of drip irrigation outweigh the disadvantages. The primary advantages are:
- Lower water use
- Less water waste
- Ease of watering
The two primary disadvantages are the necessity of routine maintenance, and the need to know and monitor your garden—since by and large you can’t see drip at work, you have to pay attention to your plants, as well as visually monitor the system.
Drip irrigation works by placing water slowly and directly into the soil—literally “dripping” it in from the many small water emitters, which are placed one or more at each plant. Drip is also excellent for watering sloped gardens because the slow rate of water applied through drip irrigation means it is more likely to soak in before it runs off.
Whether you currently hand water, use hose-end sprinklers, have an in-ground sprinkler system, or are putting in new landscape, there is a drip system for you. Some are very, very basic, and still require turning the water on by hand, on a schedule that keeps your garden properly irrigated, and others are more complex systems, with electric valves and electronic controllers—but you get to choose.
Basic Elements
PC Emitter
Installation of a basic, simple drip system is quite straightforward, and easily within the grasp of most home gardeners. It goes together much like a tubular erector set--all snapping together. Main 5/8 inch lines slip into fittings on the water source (if you’re on well water, you need a filter on the water source). If you are using ; 1/4" feeder tubes, these slip onto barbed fittings that poke into the main lines; "tee" and "el" fittings allow feeder branches to go to individual plants; continuous emitter lines snap/poke in like feeder tube then snake through areas of denser planting. The 5/8” in-line emitter tubing works similarly; you snake it through your beds or construct circles around shrubs and trees that you then connect with regular main lines.
If you already have an above-ground pressurized system, it is very simple, with a couple of plastic parts, to convert it to a drip system. So if you’re thinking of reducing some of your lawn, for example, and you already have a system that automatically waters, you’ve got the controller and underground piping for a drip system!
Advice from representatives at outlets that sell drip equipment, ranging from Friedman's to Home Depot to your local hardware store to specialist firms such as Harmony Farms in Sebastopol, Watersavers in Petaluma and Wyatt Irrigation Supplies in Santa Rosa can assist you, and make a DIY job feasible. Also, an excellent primer is Drip Irrigation in the Home Landscape, available from the University of California Agriculture and Natural Resources (Publication 21579-http://anrcatalog.ucdavis.edu/). An excellent book on drip is Drip Irrigation for Every Landscape, by Robert Kourik (out of print, but available used on Amazon.com).
Emitter Line
Water Zones
Whether you install a simple, hand-activated system, or a more complex automatic system, one key element of drip irrigation design is zoning—sometimes called hydrozoning. What this basically means is dividing the irrigation system into areas, zones and putting plants with similar water needs on their own zones. For example, you might have all pots on a sunny deck, which need water daily, or perhaps twice, on one zone. Shrubs that need weekly, or twice weekly watering would go on another zone. Trees which need less frequent, but longer watering on yet another. Sunny and shady areas might go on different zones.
Dealing with the disadvantages—Maintenance and Monitoring
You should visually monitor the system regularly. If you don’t, you won’t know that the system is not working until plants die or show severe water stress. Lines break, tube pulls away from fittings, shovels make unknown cuts, emitters plug. Look and listen for geysers, spouts, leaks, large wet areas, etc. Also monitor the health of your plants for signs of too little or too much water. You should of course do this anyway. Check the soil periodically for correct moisture. You also need to learn basic repairs and keep a toolbox of useful repair parts and tools: wire cutting pliers, regular pliers, hole punch, sturdy scissors, various connectors, sprayer heads, emitters, bubblers, emitter tubing, goof plugs, etc. But don’t be concerned if you are not mechanically minded – this stuff really is pretty easy to understand.
While involving some time, effort and cost, a properly designed and installed drip irrigation system will both save considerable water and money, and make the job of watering the garden easier.
For more detailed information, see the related article “Elements of Drip Irrigation”